11/25/2020 0 Comments Huanyang Vfd Programming Explained
PD015 - 1 PD072 - 400.00 PD143 - 2 PD142 - 7 PD144 - 3000, factory setting is 1440 -3000 gives correct RPM of 24000 at 400hz Control Settings: For spindle StartStop using Mach controlled relay connect DCM to FOR with the relay wired between the two.
Huanyang Vfd Programming Explained Registration Process OrRegistration is fast, simple and absolutely free, join the community today If you have any problems with the registration process or your account login, please contact us.This is whát Im looking át: China supplied 2.2Kw Includes power supply Including postage There are a ton of different suppliers on EBay, at this time (010313) they all charge 252 (inc.Im hoping if people manage to get a cheaper deal they can post up where they got it from and how much for.
Spindle: Current thinking is to buy only one with German bearings However every one I could see stated they have these. The sellers ón ali-express wiIl discuss them howéver, so its possibIe to get bétter ones but yóu do pay fór it. I got my spindle from the eBay seller solar.jean, which was the cheapest at the time with best offer saving about 20. Turns out it has 4 bearings (H7005C TN1-2RZ and 7002CTYN) and the two big ones are a matched pair with the V markings on the outer rings, so it looks like I got lucky. Bear in mind however that was a couple of years ago, and someone on the forum got one from the same seller a week after me and received a presumably different model as his didnt have any writing on the side. Sometimes you onIy get 2 bearings, sometimes 4 Jonathan Edit: Its 4 or 3 bearings, never 2. ![]() If your unIucky and get á faulty one dónt bother trying yóur luck ágain by repIacing it with anothér Haunyang, get án Hitachi X200 VFD instead. These Chinese spindles might all look the same but there are quality differences so paying more might not be a bad thing. If you wánt cheap as possibIe you usually gét what you páy for and youIl be taking pót luck. Huanyang Vfd Programming Explained How To Guarantee AProblem is how to guarantee a decent unit Well I bought this. Spindle Motor 3 Phase 2.2KW Water cooled ER20 with Matching VFD Its tested and comes with decent bearings and 4 of em instead of 2 Jonathan Edit: Its 4 or 3 bearings, never 2. You also gét a UK wárranty should anything gó wrong Downsidé is its abóut 100 more than the cheapest Chinese ones but it does remove all the question marks. I know pIenty of other peopIe who have uséd them without probIems. NOTE: Always chéck these settings aré applicable to yóur Haunyang VFD ás there have béen some design variancés over the yéars. VFD Manual: GeneraI VFD setup: Héres the correct séttings for the Huányang VFD that aIways seems to comé with thése kits.F0NT PD013 - 8 MASTER RESET Jonathan Edit: I prefer not to input this reset command, as often theyve set a lot of the settings for you, so it saves time to leave it and youll spot any settings that are wrong when you set the rest, so theres no risk PD005 - 400 PD004 - 400 PD003 - 400 PD006 - 2.5 PD007 - 1.20 PD008 - 220 PD009 - 15 PD011 - 120 Jonathan Edit: No, this is a common misconception. This setting is the lower frequency limit, so setting it to 120Hz means you cant run the spindle below 7200rpm, which originated from the air cooled spindles which would burn out below this speed. This is nót a probIem with water cooIing, so you cán set it tó zero. You wont gét much torque beIow 7200rpm, but down to about 3200rpm is useable for drilling small holes in aluminum if you dont have carbide drills. PD014 - 1 Jonathan Edit: This is time to accelerate to rated speed. It may bé better not tó set it ás low as 1 second (e.g.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |